The standard way of wiring the Acousti-Phonic, same as in the manual with the addition of the optional QuickSwitch for mag/both/acoustic.
The standard way of wiring the Acousti-Phonic, same as in the manual, with the Acoustic Pot with Mid/Dark Switch and a QuickSwitch (PK-0240-00 or PK-0340-00)
The standard installation for active pickups like EMG's. Shows how both the Acousti-Phonic and active pickups can run off the same battery source, from 9v ot 18v.
These connections are on the Hexpander's pass-through connector to the Acousti-phonic when they're piggybacked together, so they're the same as the standard installations for the Acousti-phonic.
The standard connections for the Hexpander pickups, optional switches, and volume pot.
Connect the Pin 7 harness in Hexpander-only installations so that mag and acoustic are available on the 13-pin connector. Note this requires the addition of an acoustic volume pot, or you can omit the pot and get acoustic out at full volume all the time by connecting the yellow and orange wires together. The QuickSwitch plugged into the Hexpander will control these signals on the 13-pin, but not on the 1/4" jack. To get mag-only on the 13-pin, just don't hook up the yellow and orange wires. To get acoustic-only on the 13-pin, just don't hook up the mags. A suitable place to connect the green wire to the mag pickup system is at the 1/4" jack.
This is how you install the Passive Volume Kit (PE-0400-00) when only using a set of ghost loaded saddles or a ghost loaded bridge without a preamp.
Use the switch in push/pull pot as the QuickSwitch but the push/pull has only 2 positions so you get mag/acoustic instead of mag/both/acoustic.
This bypass switch can be installed if you would like connect your magnetic pickups directly to the output (bypassing the Acousti-Phonic) and simultaneously forcing the board to stop consuming battery power. This can be used in the case that the battery dies and you still want to be able to play your magnetic pickups.
*Please note that there will be an audible “thump” sound when the Acousti-Phonic is turned on
This bypass switch can be installed if you would like connect your magnetic pickups directly to the output (bypassing the Acousti-Phonic) but will keep the battery connected when in the bypass mode. This will more applicable for live performance. The added passive components are used to ensure that the power switching of the Acousti-Phonic still works normally (even when the switch is in the bypassed position)
Wire a blend pot to an Acousti-Phonic. It's the same as a regular Acousti-Phonic installation, only the mag pot is reverse0wired to work in the opposite direction. Note that you actually get more control over your sound with separate pots because it allows you to control how hard each pickup drives effects down the line. A blend pot always mixes one signal at full-volume with the other at partial volume.
This operates the Acousti-Phonic in Mono mode only with power switched by the Ring and Sleeve contacts of a standard, stereo, TRS jack. This may be a useful option for guitars that can't use the Stereo Switched Jack, such a those with a deep barrel jack. There is no stereo mode available in this configuration.
This is a solution for guitars with deep barrel jacks. The Switchcraft Switchjack has four lugs like the Stereo Switched Jack that comes with the Acousti-Phonic, but the switch works in the opposite way, so it can't be wired the same. This wiring delivers both Mono and Stereo modes. Note the Switchjack is designed for acoustic guitars and comes with a strap-nut, but this can be removed and replace with a regular but for use with electric guitars.
The mags go straight to the ring of the Stereo Switched jack, instead of going through the Acousti-Phonic (true bypass). There is no blended (mono) mode available in this configuration. When you insert a stereo 1/4" plug you get mags on the Ring and acoustic on the Tip. When you insert a mono 1/4" plug, you get acoustic on the Tip only. The Acousti-Phonic is held in mono mode by grounding the ring contact permanently, but the signal going into it is acoustic, so that's all that appears on the Tip.
This clever circuit requires a second Stereo Switched Jack. When you plug into the second jack, you get your magnetic pickups straight out (true bypass). Acoustic sound in available on the first jack but the second jack empty, the first jack has both magnetic and acoustic, in either Mono or Stereo mode.
Mags go straight out to one 1/4" jack (true bypass) and acoustic goes to another 1/4" jack, the Stereo Switched Jack that comes with the Acousti-Phonic. The Acousti-Phonic is help in mono mode by grounding the ring contact permanently, but the only signal going into it is acoustic, so that's all that appears on the Tip. There is no Blend mode in this configuration.
Dual jacks with blended signals available when a mono plug is inserted in the Stereo Switched Jack only. When a mono 1/4" plug is inserted the second jack (also a Stereo Switched Jack), mag is on the first